Anchor MPA-4500
Part of the Liberty sound system series. Switchable to either an efficient voice-projecting system or a full-range music quality system. Features a 70 watt amplifier, two XLR balanced phantom-powered mic inputs, 1/4" line input, line output, treble and bass controls, 12 volt DC output and 1/4" speaker output.
•Also available: MPB-4500 battery-powered with built-in charger

Anchor PA-2500
Part of the Explorer sound system series. Features a 50-watt amplifier and two-way speaker system with seperate bass and treble controls. Inputs include a balanced, low-impedance XLR mic input with phantom power, an unbalanced 1/4" phone mic input and a line level input with 1/4" phone and RCA jack. Also features an RCA line output and an unswitched 8ohm speaker output.
•Also available: PB-2500 battery-powered with built-in charger.

Anchor Companion Speaker
Available in the Liberty, Explorer and Voyager sound systems. Unpowered speaker that connects to your amplified speaker via an optional speaker cable.

Anchor AN-1000X
Full-range powered speaker that includes RCA and 1/4" phone line-level inputs, mic/line configurable XLR balanced input, and both line-level (RCA) and external speaker output. Features a 50 watt amplifier, shielded-magnet speakers, and separate bass, treble and volume controls on the front panel.

Anchor AN-130
Two-way powered speaker with 1/4" phone microphone and instrument-level inputs, plus two RCA-type summing line-level inputs. Features a 25-watt amplifier, separate bass and treble controls and a shield-magnet speaker.
Also available: AN-130DC includes DC output jack

Electro-Voice® Plasma P1
The Electro-Voice® Plasma P1 integrates premium EV transducers with high-power Class-H amplification and signal processing to provide an outstanding combination of sonic detail, SPL, and ease of use. A EVX155 15" LF transducer uses a Kevlar®-reinforced cone with RMD® driven by a 4" voice coil for well-defined transient response, while maintaining articulate vocals at all SPLs. A proprietary ND6 compression driver with a 3" diaphragm and 1.4" exit provides extended HF response with very low distortion. A Class-H two-channel amplifier requires no fans for quiet operation, low maintenance, and long-term reliability. Coupled with signal processing for linear acoustic response and unobtrusive protection, the amplifier delivers the power required for high-level reinforcement. Dynamic linearity is another benefit of amplifiers designed for system integration with large-format transducer motors.
L-track is embedded into the Plasma P1 to provide convenient multi-axis suspension and attachment points for an optional suspension arm. The very compact multi-angle enclosure can be used either in monitor position (in left and right configurations) or arrayed.
   The Plasma P1 is acoustically designed for uniform coverage in both horizontal and vertical planes adding to its versatility. The P1's applications are for where the highest quality sound is required: theater, A/V, stage monitoring, and sound reinforcement.

Fostex 6301 BEAV
Small, portable, versatile monitor that delivers impressive sound. Use in pairs or alone. Ideal for use with instruments in project studios, on stage, in remote recording vehicles, video productions & multimedia presentations.

MAIN FEATURES
• Magnetically shielded type 10cm full range speaker
• XLR & 1/4 in. inputs
• Built in 10W RMS power amplifier
• Power on/off switch
• Rotary level control
• EXT SP terminal
• Automated protection circuit
• Lightweight yet rugged enclosure
• Compact size & high quality sound output
• Optional 9610 Bracket (vertical / horizontal)

Fostex PS 3.1 Personal Monitors
The PS-3.1 offers a complete 2-way monitoring solution, combining one 5-1/4" bass reflex subwoofer and a pair of matching shielded satellite speakers with 3" full-range drivers in a compact, affordable package. The subwoofer contains its own 15 watt power amplifier, a crossover network, and two 5 watt power amplifiers for powering the satellite speakers—making the PS-3.1 a self-contained system that fits nearly any studio application without the need for external amplification. Satellite dimensions are 7-1/4"H x 6-9/16"D x 4-11/16"W, weight 3lbs 7oz each. Subwoofer 10"H x 11-1/4"D x 8-1/4"W, weight 14 lbs.

MAIN FEATURES
• One 5-1/4" bass reflex subwoofer with 15 watt power amplifier
• 2 shielded satellite speakers with 3" full-range drivers with 5 watt power amplifiers
• Crossover network
• System response 80Hz-20kHz.

JBL Eon Power 10
The speakers that started the portable powered speaker revolution. Portable, practical and powerful, EON provides solutions for your entire sound system.

The new EON10 G2 compact powered speaker features a 10" woofer, increased power and a three input mini-mixer. The EON10 G2 is ideal for AV applications, smaller musical and spoken word performances and, when combined with the new EONSUB G2 powered subwoofer, provides a full range sound system for small and medium sized events.
   The first generation EON10 was very popular, not only with musicians, but with hotels, meeting planners, AV companies and just about any application where portable compact sound reinforcement was needed. Its successor, EON10 G2 offers more power, more flexibility and a refined appearance that will make it even more appropriate for its many types of users.

JBL Eon Power 15
With more than 300,000 systems already being used in applications from live sound reinforcement, speech and vocals to music playback in entertainment, A/V and institutional environments, the JBL EON system is firmly entrenched as the industry leader in powered portable speaker systems.
   The flagship of the new series is the JBL EON15 G2, delivering 300 watts of power to a 15" neodymium Differential Drive® LF driver. The driver boasts a dual neodymium magnet and dual voice coil motor that efficiently delivers high output from a lightweight woofer. Meanwhile, the HF amplifier delivers 100 watts of power to a 1.75" titanium diaphragm compression driver with Ferro-fluid cooling.

JBL SR-X Series
The new SR-X Series was designed for these most discerning users, with 11 models that embody the superior engineering, unsurpassed tour sound performance, legendary reliability and value inherent in the JBL name. Start with the SR-X's advanced DuraFlex™ finish. Add their all-new networks. Top them off with the same components found in 9 out of 10 speaker systems on the road with today's top touring acts*. All wrapped up in a speaker whose lineage is connected by a solid line of leadership more than half a century long.
While each SR-X speaker has a personality all its own, the line as a whole delivers a remarkable range of options. In fact, the SR-X line is the most complete line of high performance portable speakers available today, with a model for virtually every application. Whether your needs call for SR-X subwoofers, SR-X front-of-house systems or SR-X stage monitors, you can be assured of owning a speaker that represents a new standard; a standard that will satisfy even the toughest of critics.

JBL E-System 15
A complete sound reinforcement system so good that no one company could build it all. Start with a second generation of the speaker that started the powered-speaker revolution - the JBL EON15-G2 featuring 400 watts of bi-amplified power (300 watts for low frequencies and 100 watts for high frequencies). The EON15-G2 is at home as a main PA speaker or as a vocal or instrument monitor.
Then add  a Soundcraft E-8 mixer with that great British sound and features:

• 8 mono input channels plus two stereo inputs

• 2 aux sends, each globally switchable pre or post fader

• 100mm faders

• Internal power supply

• Simple rack mounting options

• 3 band EQ with swept mid band

• Precision, ultra-linear mic pre-amps

• True, professional +48V phantom power

• Individual channel mutes

To complete the system, a pair of AKG D2000S microphones are included. These handheld, dynamic, hypercardiod microphones are at home in a variety of sound reinforcement applications for speech, vocals and instruments. Rounding out the system are four 25" XLR cables to hook it all together.

Mackie SRM 350
2-Way Active Loudspeaker System
Studio-Quality Sound in a World of Honky, Disgusting PA Speakers.
The SRM350 brings studio-monitor sound quality to a world inundated with big, inefficient PA speakers. This 2-way bi-amplified active loudspeaker easily out-performs the competitions’ larger active models thanks to the combined efforts of the Mackie Active Engineering and world-class EAW Loudspeaker Design teams. With innovative Dynamic Bass Boost for full sound at all volume levels, a Contour control for precision response, and — most importantly — award-winning Mackie Active speaker design, the SRM350 is in a class all its own.

Mackie SRM 450
Precision 2-way, bi-amplified active PA speaker.
Before you read this, press your mental RESET button.
Forget about what other small PA speakers sound like. Especially forget what so-called "powered" speakers sound like. The active SRM450 is that different.
It has tight, steel-fisted bass to below 55Hz and detailed, articulate treble out to 20,000Hz. Midrange is warm, natural, and free from ear-fatiguing harshness. The SRM450 has astonishingly wide dispersion that lets your whole audience hear clearly, whether they're in the front, back, or way out on the sides of the room.
And above all, the SRM450 cranks! Without a hint of distortion, it effortlessly achieves sound pressure levels that would melt conventional speakers into a pile of molten slag.

Mackie C-300
Huge Power Handling – Superb Dispersion
The C300 (Speakon®) and the C300i (1/4 inch) uses the same basic transducers as the active SRM450 – with two differences. TheC300/C300i's 1.75-inch high frequency compression driver uses a composite mylar diaphragm; the12-inch low frequency transducer incorporates a 3-inch Inside/Outside temperature- resistant voice coil. Both of these compensate for the fact that the speaker system must be able to handle a wide range of external power inputs (including our mega-powered PPM808S or PPM808M).
The C300/C300i uses the same studio-quality horn assembly with multi-cell aperture horn throat and large format exponential/conical high-frequency horn mouth for superb dispersion. This means everyone in your audience hears clearly... not just the people in the middle between the speakers.
   And like the SRM450, the C300/C300i has the same asymmetrical trapezoidal cabinet for minimum internal resonance and the ability to recline for floor monitor use. And the same weight-balanced enclosure with dual side handles and top handle, built-in pole mount and ten built-in hanging points. But instead of internal amplification, the C300/C300i has a Low-Impedance Compensated Crossover (LICC) with full built-in transducer protection and Speakon® or TS(Tip-Sleeve) inputs that just beg to be energized to shock volumes with a PPM mixer or FR Series power amplifier.

Tannoy Reveal Active Monitor
For those on a budget, the Reveal provides a high quality monitor with real high-end features. The distinctive cabinet has been designed to offer increased structural integrity and reduced HF diffraction effects. Its unique 1 ¼" thick contoured MDF baffle provides a solid foundation for drive unit mounting as well as increasing overall stiffness. This means a clean and articulate performance for whatever project you have in mind. Reveal's drive units include a 1" soft dome tweeter and 6 1/2" bass unit manufactured in-house by Tannoy, ensuring quality and consistency in use. Both units are also magnetically shielded, so the Reveal can be positioned close to video monitors if desired. High power handling capability coupled with above average sensitivity means that Reveal can produce high SPL's without distortion. There is no better value on the market today.

Tannoy Proto-J Nearfield
The Proto-J is the latest playback monitor from Tannoy. It has an extremely detailed, dynamic sound with a wide, flat frequency response - all of which are essential for monitoring with reliable accuracy. The 3/4" soft dome HF unit is seamlessly matched to a 6.5" long throw bass unit by the precision low-loss crossover network. The drive units are discretely mounted on a 3/4" MDF baffle. The front edges of the vented enclosure are chamfered to reduce high frequency diffraction. The back panel features two 5 way binding post inputs and integral inserts to accommodate OmniMount™ 20.0 (formerly 50) Series wall brackets that allows wall mounting for easy and flexible 5.1 surround sound installs. Proto-J is designed to compliment the Tannoy PS 110B 5.1 Subwoofer as a complete package.

Yamaha - MS101 II Powered Speaker
Why bother with separate amp, speaker and interconnecting cable when the MS101 II self-powered speaker will fill the bill? Features include two unbalanced line inputs, one unbalanced mic input and bass and treble controls. Magnetically shielded for AV applications. Output Power - 10 watts; Frequency Response - 75 to 18,000 Hz; AC Power Requirements - 110 to 125 V AC, 50 to 60 Hz; Dimensions - 8 7/16" H x 5 3/4" W x 7 9/16" D; Weight - Approx. 5 lbs.

Yamaha - MSP5 Bi-Amplified Studio Monitor
The MSP-5 bi-amplified monitor speaker delivers extraordinary sound quality providing a perfect choice for a wide range of applications from home studios to post production. With two separate amplifiers powering the custom designed 5" woofer and 1" Titanium tweeter, incredibly lower distortion is realized. A total of 67 watts, 40 to the woofer and 27 to the tweeter, generates a much larger sound field than would normally be expected from a system of this size. Complete magnetic shielding and compact size permits easy placement near all types of audio, video and computer equipment. Frequency Response - 50 Hz to 40 kHz; Dimensions - 11" H x 6 5/8" W x 8 3/4" D; Weight - 16.5 lbs.

Electro-Voice 7100
A single-rack-space unit that is perfect for studio applications and for powering the high end of multiway systems. Convection cooled for silent operation. Features on the front panel include left and right channel volume knobs and headphone jack (for studio use).
•Watts: 145 per channel (4)
•100 per channel (8)

Mackie M•800
Ultra-low-noise/ low-distortion designed amplifier. Fast Recovery circuitry reduces distortion at the edge of clipping and beyond. Two 2nd order, 12dB/octave, Bessel low-cut filters with variable frequency from Off to 170Hz help optimize bass output of your sound system. Constant directivity horn EQ/Air EQ with variable frequency from 2k to 6kHz and on/off switch Limiter with On/Off switch (decreases distortion that may become present when the M•800 is driven at max levels without affecting overall sound levels). XLR thru outputs, 1/4" jacks and 5-way binding post outputs. Detented gain controls calibrated in dB & volts Signal present and OL LEDs with Channel Status LEDs. Easily handles 2-ohm loads all night long. Features superior T-Design cooling.
•800 watts @ 4 ohms bridged
•550 watts @ 8 ohms bridged
•400 + 400 watts @ 2 ohms
•stereo 275 + 275 watts @ 4 ohms stereo
•140 + 140 watts @ 8 ohms stereo

Mackie M•1400
Part of the FR (Fast Recovery) Series. The FR system is a circuit deign that quickly recovers from the consequences of being driven in extreme conditions. Includes 1/4" inputs and outputs, 3/4" binding post outputs, male and female XLR input/throughput, variable low cut filter (5Hz to 170Hz), amp mode switch (stereo, mono, bridged), output mode switch (limiter on/off, subwoofer), subwoofer crossover select switch (125Hz, 63Hz) and more.
•Watts: 500 per channel (4)
•300 per channel (8)

Mackie M•2600
Ultra-low-noise/ low-distortion designed amplifier. Fast Recovery circuitry reduces distortion at the edge of clipping and beyond. Two 2nd order, 12dB/octave, Bessel low-cut filters with variable frequency from Off to 170Hz help optimize bass output of your sound system. Two 4th order, 24dB/octave, Linkwith-Riley subwoofer crossovers with three selectable frequencies Limiter with On/Off switch (decreases distortion that may become present when the M•2600 is driven at max levels without affecting overall sound levels). XLR thru outputs, Speakon connectors and 5-way binding post outputs. Detented gain controls calibrated in dB & volts. Signal present and OL LEDs, Channel Status LEDs Easily handles 2-ohm loads all night long. Features superior T-Design cooling.
•2600 watts @ 4 ohms bridged
•1700 watts @ 8 ohms bridged
•1300 + 1300 watts @ 2 ohms stereo
•850 + 850 watts @ 4 ohms stereo
•500 + 500 watts @ 8 ohms stereo

QSC PLX Series
A line of amplifiers that defines high impact. Up to 3,400 watts in a 2 rack-unit chassis that's only 13" deep and 21 lbs. We included our exclusive PowerWave Technology used in our award-winning PowerLight Series for chest-pounding bass and crystal-clear highs. It also features hum-free noise floor and ultra-low distortion of .03% THD. To keep PLX running under the most demanding conditions, we've even added our Advanced Thermal Management System. PLXs offer the reliability of a company that's been building professional amplifiers for over 30 years.

QSC ISA Series
Designed as a cost-effective solution specifically for sound contractors, the ISA Series features seven models including four low impedance models (ISA 280, ISA 450, ISA 750, ISA 1350) rated for 2-ohm operation, and three "Ti" versions with isolated 25, 70 and 100 volt outputs for distributed audio systems (ISA 300Ti, ISA 500Ti, ISA 800Ti). Versatile loading options and a comprehensive feature set make the ISA Series a rugged, cost-effective power solution for any permanently installed sound system.
Unique among distributed sound power amplifiers, the "Ti" versions will drive 8- or 4-ohm loads and a distributed system on the same channel simultaneously. This enables a contractor to reduce the number of required amplifier channels by allowing a limited number of distributed speakers to be attached to the same amp as is powering the main sound system.
Housed in a rugged 3-U chassis, all seven models feature rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings. Inputs include both XLR and detachable Euro-style connectors. Outputs feature covered barrier strip connectors for safety agency compliance, and for added versatility, a DataPort V2 (Version 2) terminated with an HD-15 connector is provided for use with DPV2-compatible signal processing accessories such as the XC-3 Crossover, SF-3 Subwoofer Filter, LF-3 Low Frequency Filter and the DSP-3 with external power supply.
Selectable high-pass filters are included to protect speakers and prevent speaker transformer saturation with minimal effect on program material. The ISA Series provide additional protection circuitry including DC, infrasonic, thermal overload, RF and short circuit protection.
On the ISA 750 and ISA 800Ti, class H complementary bipolar output circuitry increases system efficiency by reducing AC power draw and waste heat by 40%. Cooling is accomplished via an automatic variable speed fan, which pulls air from back to front.